OPEN ACCESS

Articles online

Exposure Assessment of Particulate Matter from Abrasive Treatment of Carbon and Glass Fibre-Reinforced Epoxy-Composites – Two Case Studies

Category: Air Toxics

Volume: 15 | Issue: 5 | Pages: 1906-1916
DOI: 10.4209/aaqr.2015.02.0086
PDF | Supplemental material | RIS | BibTeX

Alexander C.Ø. Jensen 1, Marcus Levin1,2, Antti J. Koivisto1, Kirsten I. Kling1, Anne T. Saber1, Ismo K. Koponen1

  • 1 National Research Centre for the Working Environment, Lersø Parkallé 105, Copenhagen DK-2100, Denmark
  • 2 Department of Micro- and Nanotechnology, Technical University of Denmark, DK-2800, Lyngby, Denmark

Highlights

Sanding of fibre-reinforced epoxy composites spatial concentrations up to 1.7 × 106.
Local ventilation, tent PF, and working style were studied on concentration levels.
Electron microscopy show epoxy fragments and fibres.
Inhaled dose rates were calculated.
Short toxicological review of fibres present in the composite.


Abstract

The use of composites is ever increasing due to their important structural and chemical features. The composite component production often involves high energy grinding and sanding processes to which emissions workers are potentially exposed. In this study we investigated the machining of carbon and glass fibre-reinforced epoxy composite materials at two facilities. We measured particle number concentrations and size distributions of the released material in near field and far field during sanding of glass- and carbon fibre-reinforced composites. We assessed the means of reducing exposure during the work by means of different working style, local exhaust ventilation, and enclosing the process area. Machining processes released particles primarily in < 100 nm size range. Without enclosure, process particle concentrations were 3.9 × 104 cm–3 in the near field and 1.3 × 104 cm–3 in the far field. Therefore workers in the same area may not be aware of being exposed to the process particles and the need of wearing protective outfits. Comparison of workers working style and effect on near field particle concentrations showed that a careless working style increased particle concentrations of 1.1% and 14.1% when comparing with a careful working style. Investigating the effect of the local exhaust ventilation showed that a maximum flow rate caused removal of close to 100% of particles from the working zone. A 28% reduction in the flow rate reduced particle removal efficiency more than 50%. With the enclosure around the process area, the process particle concentrations were 1.7 × 106 cm–3 in the near field, while the concentration in the far field was negligible. The enclosure used was shown to provide an average protection factor of more than 100.

Keywords

Aerosol Nanoparticle Occupational hygiene Emission control Sanding


Related Article

Characterization of Particulate Matter Profiling and Alveolar Deposition from Biomass Burning in Northern Thailand: The 7-SEAS Study

Hsiao-Chi Chuang, Ta-Chih Hsiao , Sheng-Hsiang Wang, Si-Chee Tsay, Neng-Huei Lin
Volume: 16 | Issue: 11 | Pages: 2897-2906
DOI: 10.4209/aaqr.2015.08.0502
PDF | Supplemental material

A Low Pressure Drop Preseparator for Elimination of Particles Larger than 450 nm

C. Asbach , H. Fissan, H. Kaminski, T.A.J. Kuhlbusch, D.Y.H. Pui, H. Shin, H.G. Horn, T. Hase
Volume: 11 | Issue: 5 | Pages: 487-496
DOI: 10.4209/aaqr.2011.05.0057
PDF

Size Distribution of Inorganic Elements in Bottom Ashes from Seven Types of Bio-Fuels across Beijing-Tianjin-Hebei Region, China

Zhiyong Li , Huiqiao Ma, Fan Lin, Peng Zhao, Lei Wang, Yunjun Jiang, Caixiu An, Aiqin Liu, Zishu Hu, Hui Jin
Accepted Manuscripts
DOI: 10.4209/aaqr.2017.08.0296
PDF

Seasonal Trends of Atmospheric PAHs in Five Asian Megacities and Source Detection Using Suitable Biomarkers

Mahua Saha, Dusmant Maharana, Rina Kurumisawa, Hideshige Takada , Bee Geok Yeo, Andrea C. Rodrigues, Badal Bhattacharya, Hidetoshi Kumata, Tomoaki Okuda, Kebin He, Yongliang Ma, Fumiyuki Nakajima, Mohamad Pauzi Zakaria, Duong Hoang Giang, Pham Hung Viet
Volume: 17 | Issue: 9 | Pages: 2247-2262
DOI: 10.4209/aaqr.2017.05.0163
PDF | Supplemental material
;