OPEN ACCESS

Articles online

Development of a Reliable and Cost-Effective Weighing Chamber for Aerosol Sample Analyses

Category: Aerosol Physics and Instrumentation

Volume: 15 | Issue: 3 | Pages: 749-758
DOI: 10.4209/aaqr.2014.10.0260
PDF | RIS | BibTeX

Yu-Mei Kuo1, Chia-Wei Hsu2, Jen-Ying Chen2, Sheng-Hsiu Huang2, Lien-Hsiung Lee3, Chih-Chieh Chen 2

  • 1 Department of Occupational Safety and Health, Chung Hwa University of Medical Technology, No. 89, Wen-Hwa 1st Street, Jen-Te District, Tainan 717, Taiwan
  • 2 Institute of Occupational Medicine and Industrial Hygiene, College of Public Health, National Taiwan University, Rm. 718, No. 17, Xu-Zhou Rd., Taipei 100, Taiwan
  • 3 Institute of Labor, Occupational Safety and Health, No. 99, Ln. 407, Hengke Rd., Sijhih District, New Taipei City 221, Taiwan

Highlights

A reliable and cost-effective weighing chamber is developed.
Electrostatic charge neutralization can improve the weighing quality.
A radioactive source is a better choice for electrostatic charge elimination.
Gloves should be worn to conduct filter weighing.
Opening the filter holder’s lid expedite the filter conditioning.


Abstract

Reliable gravimetric analysis of particulate matter filters is of great importance in exposure and risk assessment in industrial hygiene and environmental health, especially for light weight fine particles like PM2.5. Weighing bias may be caused by a number of environmental and operational factors. Among them, the humidity effect is most often addressed. This study proposes a cost-effective weighing chamber with humidity control by using a saturated magnesium chloride solution to meet the USEPA requirements for filter weighing. To exclude the interference of electrostatic charges, filter samples are treated with a radioactive source, Am241, on a microbalance pan before weighing. The results of long term monitoring showed that the relative humidity inside the weighing chamber is between 31–35%, when the temperature is between 18–21°C. The air pressure inside the weighing chamber is kept slightly positive by adjusting the air supply of the humidity control unit at 15 L/min during filter conditioning and at 25 L/min during filter weighing to maintain a stable humidity condition and prevent aerosol contamination from outside. Moreover, the operator should wear gloves to prevent hand moisture evaporation. We suggest that filter samples to be stored and conditioned in a weighing chamber with the filter holder’s lid open to expedite and enhance the filter conditioning. When a hygroscopic filter, such as an MCE, is used to collect about 0.5 mg of hygroscopic NaCl particles, a mass increase of 0.5 mg results occurs due to the filter. An additional 1.2 mg mass increase occurs due to collected NaCl particles, when the weighing is performed under RH 85% rather than in the environmentally-well-controlled weighing chamber. With the use of the weighing chamber and the recommended practices, this study demonstrates excellent weighing quality. The mass determination limits are below 3 µg for 37-mm particle-laden filter samples commonly encountered in practical situations.

Keywords

Weighing chamber Humidity Electrostatic charge Filter samples


Related Article

Validation of MicroAeth® as a Black Carbon Monitor for Fixed-Site Measurement and Optimization for Personal Exposure Characterization

Jing Cai, Beizhan Yan, James Ross, Danian Zhang, Patrick L. Kinney, Matthew S. Perzanowski, KyungHwa Jung, Rachel Miller, Steven N. Chillrud
Volume: 14 | Issue: 1 | Pages: 1-9
DOI: 10.4209/aaqr.2013.03.0088
PDF

The Construction and Application of a Multipoint Sampling System for Vehicle Exhaust Plumes

Xianbao Shen, Zhiliang Yao , Kebin He , Xinyue Cao, Huan Liu
Volume: 17 | Issue: 7 | Pages: 1705-1716
DOI: 10.4209/aaqr.2017.02.0076
PDF

Performance Estimation of a Louver Dust Collector Attached to the Bottom of a Subway Train Running in a Tunnel

Jung-Bo Sim, Sang-Hee Woo, Won-Geun Kim, Se-Jin Yook , Jong Bum Kim, Gwi-Nam Bae, Hwa Hyun Yoon
Accepted Manuscripts
DOI: 10.4209/aaqr.2017.01.0043
PDF
;